ADEMCO LYNX Uživatelská příručka stáhnout pdf

K5966-2 9/06 Rev. A

ADEMCO LYNXR-ENSIA

Security System

Quick Start Guide

LYNXR-ENSIA is not intended for UL985 Household Fire applications unless a 24-hour backup battery

(P/N LYNXRCHKIT-HC) is installed.

Introduction

This Quick Start Guide can help you install the rechargeable LYNXR-ENSIA quickly and easily by providing the

basic steps for installation using the built-in defaults. For more detailed information and important notes, refer to

the LYNXR-ENSIA Installation Instructions.

Note: The following steps assume that one of the system’s default tables will be used.

Installing LYNXR-ENSIA

Installation and Electrical Connections

Step Action

1. Install the control as follows:

a. Separate the front assembly from the back plate and disconnect the cable from the front assembly board.

Note: Disconnect the cable only from the front assembly board, not from the terminal block PC board.

b. Mount the back plate.

2. Make wiring connections as follows:

a. Connect the incoming phone line to either the 8-position jack or terminals 2 (TIP) and 3 (RING).

b. Connect the handset phone lines to either the RJ11 jack or terminals 4 (TIP) and 5 (RING).

Note: For full line seize operation, see the installation instructions.

c. If used, connect a piezo sounder to terminals 10 (+) and 11 (–).

d. If used, connect a bell to terminals 11 (–) and 12 (+).

e. If using Powerline Carrier Devices, connect com/data/sync/ lines from the 1332X10 transformer to terminals 9,

13, and 14 respectively.

Note: Install Powerline Carrier Devices according to their instructions.

f. Connect wires from the 1332/1332X10 AC Transformer to terminals 15 and 16.

3. Make battery connections as follows:

a. Remove battery retainer.

b. Remove backing from tape on back plate.

c. Insert battery pack into back plate.

d. Install battery retainer.

e. Connect battery connector to receptacle on terminal block PC board.

f. Carefully reconnect the ribbon cable to the front assembly PC board connector (properly aligning the red wire).

g. After all wiring connections have been made, snap the front assembly to the back plate so it is held by the

locking tabs.

h. Plug the transformer into a 24-hour, 110VAC unswitched outlet.

Note: Rechargeable batteries may take up to 48-hours to fully charge. “LOW BAT” message should clear within four

hours, or by entering Test Mode.

- 1 -

1 2 3 4 5 6 7 8

Shrnutí obsahu

Strany 1 - Security System

K5966-2 9/06 Rev. A ADEMCO LYNXR-ENSIA Security System Quick Start Guide UUUULLLL LYNXR-ENSIA is not intended for UL985 Household Fire a

Strany 2 - CARRIER DEVICES

DISCONNECT THIS END ONLY!MXXXXK5108RED WIREMARKINGLOCKING TABSPC BOARDPART NUMBERLOCATIONPC BOARDPART NUMBERLOCATION06000-003-V0 01009-007-V01BATTERYR

Strany 3 - System Programming

System Programming For advanced interactive mode programming refer to the end of the System Programming procedure. Step Action 1. Enter Programming m

Strany 4 - Interactive mode programming

Step Action 4. (Cont.) 5) When the last zone has been entered, the display will remain on that zone. To exit this mode and return to data field pro

Strany 5

LYNXR-ENSIA PROGRAMMING DEFAULT TABLES (boldface indicates defaults that differ between tables) For programming data values and Powerline Carrier Devi

Strany 6 - 06000-012-V0

Zone Table 1 Table 2 Table 3 Table 4 1 ------- ------- ------- ------- 2 front door front door front door front door 3 back door back d

Strany 7 - Keypad Functions

Keypad Functions Security Functions Checking system status: STATUS (high level messages); press STATUS again for secondary messages. To arm in

Strany 8 - ‡K5966-2OŠ

Remote Phone Control Operation To remotely disarm system: + [1] To remotely arm in AWAY mode: