ADEMCO Vista-50 Uživatelský manuál

VISTA50P-PR 8/95 (See Instructions N5944-6)VISTA-50PVISTA-50PULPARTITIONED SECURITY SYSTEMwith SCHEDULINGQuick StartStep-by-Step Programming Procedu

Ð 10 Ð1*17 LOBBY PARTITION [0] Enter the "common lobby" partition (1-8)1*18 AFFECTS LOBBY [0] Enter 1 if this partition affects the co

Ð 11 Ð1*75 RELAY TIMEOUT YY SECONDS [000] | | Enter the relay timeout, 0-127 seconds, desired for #80 MenuMode time driven event relay command

Ð 12 ÐNOTES:

Ð 13 ÐVISTA 50P/VISTA 50-PULMULTIPLE PARTITION PROGRAMMING FORMSome fields are programmed for each partition (shown as shaded fields). See the PARTI

Ð 14 Ð*48 LOW SPEED FORMAT (Sec.) [0] 0=Ademco Low Speed; 1=Sescoa/Radionics*49 CHECKSUM VERIFICATION [0] [0] 1=yes; 0=no PrimScndry*50 SESC

Ð 15 Ð*83 FIRST TEST REPORT TIME | | | [Day 00; hour 12; min 00] Days 01-07 Hours 00-23 Min 00-59;00 in all boxes=i

Ð 16 ÐNON-ALARM DIALER CODES ( Armed Stay, Time Set & Event Logging)1*40 First Digit 1*41 Second DigitArmed STAY | | Time/Date set or even

Ð 17 Ð3rd Page Programming Fields(press *94) PARTITIONING SETUP FIELDSRefer to the PARTITION-SPECIFIC program fields for programming each partitionÕ

Ð 18 ÐPARTITION-SPECIFIC FIELDS(Duplicate this page for each partition in the installation.)To program these fields,1. Press *91 and select a partitio

Ð 19 ÐPROGRAMMING WITH #93 MENU MODENOTE: The following fields should be preset before beginning: 2*00 Number of Partitions;1*32 receiver type. In a

Ð 2Ð

Ð 20 ÐSYSTEM LAYOUT WORKSHEETSAs with any security system, you should first define the installation. This includes determininghow many partitions will

Ð 21 ÐSYSTEM DEFINITIONS BY PARTITION (enter values or yes/no)Option part 1 part. 2 part. 3 part. 4 part. 5 part. 6 part. 7 part. 8Entry Delay #1 (1

Ð 22 ÐACCESS CODES & USER DEFINITIONS FOR PARTITIONS 1-34-digit Access Partition 1 Partition 2 Partition 3Security Group 2-digit Auth. ope

Ð 23 ÐZONE DEFINITIONS FOR ZONES 1-24DIP DIP † Enter loop number on moduleParti- RF Trans. Type†RPM RPM Loop number must be 1 for hardwire and D

Ð 24 ÐZONE DEFINITIONS FOR ZONES 25-48DIP DIP †Enter loop number on moduleParti- RF Trans. Type†RPM RPM Loop number must be 1 for hardwire and D

Ð 25 ÐZONE DEFINITIONS FOR ZONES 49-72DIP DIP † Enter loop number on moduleParti- RF Trans. Type†RPM RPM Loop number must be 1 for hardwire and

ZONE DEFINITIONS FOR ZONES 73-86DIP DIP † Enter loop number on moduleParti- RF Trans. Type†RPM RPM Loop number must be 1 for hardwire and DIP de

Ð 27 ÐNOTES:

ALARM DEVICE MANUFACTURING CORPORATIONA DIVISION OF PITTWAY CORPORATION165 Eileen Way, Syosset, New York 11791Copyright © 1994 PITTWAY CORPORATION

Ð 3 ÐTABLE OF CONTENTSSUMMARY OF PROGRAMMING COMMANDS... 2RECOMMEN

Ð 4ÐRecommended Programming ProcedureThe following is a step-by-step procedure recommended for programmingyour VISTA-50P/VISTA-50PUL system.1 . Set th

Ð 5 Ð1 1 . Use #93 Menu Mode for programming relay voice descriptorsand custom word substitutes.Refer to the RELAY VOICE DESCRIPTORS section for furth

Ð 6ÐPROGRAM FIELD CATEGORIESIn the following pages, the programming fields have been arranged by category. Use this index to cross referencethe numer

Ð 7 ÐVISTA 50P/VISTA 50-PULSINGLE PARTITION PROGRAMMING FORMStandard default (*97) values are shown in brackets [ ], otherwise default = 0. Fields

Ð 8 Ð*43 DIAL TONE DETECTION [1] 1=wait for true dial tone; 0=pause, then dial*44 RING DETECTION COUNT [00] | 01-14; 15=answeri

Ð 9 ÐSYSTEM NON ALARM CODES*81 *82First Digit Second DigitClose | | Open | | Low Battery | | Low Bat Res | | AC Loss |