ADEMCO 4120XM Uživatelská příručka Strana 30

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 80
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 29
..-. ---- .
user Goaes 4kLevels of
Authority (cont.)
Assigning or
Deleting Temporary
Codes By User 2
(Master User)
To Assign A Temporary
Code:
Temporary Code
(User 3)
Duress Code
Babysitter Code
(User 22)
Important!:
Can perform all system functions (Arm, Disarm, Bypass,
etc.) using the temporaty code programmed by User 2
(Master).
May add, delete, change temporary codes for Users 04
through 69 (User3 cannot change User 02’s or 70’s
code).
The duress code is a means of sending a silent alarm to
a central monitoring station if the user is being forced to
disarm (or arm) the system under threat. This feature is
only useful if the system is connected
to a central
station.
The Duress code is simply the usual security code, but
with the fourth digit increased
by one (e.g., if code is 1-2-
3-4, duress code is 1-2-3-5).
When the system’s Auxiliary Voltage Triggers are
connected to another communication’s media (Derived
Channel/Long Range Radio), note that duress is
signaled on the same trigger that signals silent panic
(whereas duress has its own unique report when digitally
communicated).
When used, the system will disarm (or arm), but will also
send a silent ala~m to the central station” (if service is
connected). There will be no indication at the console
that an alarm was sent.
This code is usually assigned to those who have a need
to arm and disarm the system at specific times only (e.g.,
a babysitter needs to control the system only when
babysitting).
If field 1*5O is enabled, the code assigned to User 22
cannot be used to disarm the system
unless the
system was
armed with that code.
Temorary users, such as babysitters, should not be
shown how to bypass zones when arming.
Unless Ademco Contact ID reporting is used, only user codes #1 - #15 can
uniquely report to the central station ~sing the communication formats provided.
Users #16 - #70 will report as User#15, if enabled for open/close reporting, for
the other reporting formats,
1.
2.
3.
4
The Master or Primary User (User 2) can assign or delete temporary codes for
Users 03 through 70.
User numbers must be entered as 2-digit entries. Single digit user numbers
must, therefore, always be preceded by a “O” (example, 03, 04, 05, etc.).
Make sure the end user understands this requirement.
The system will emit a single beep when each temporary code has been
successfully entered. If the 6-digit code feature is in effect (field 1
54),
temporary users must also use 6-digit codes (2-digit User # + 4-digit code).
It is recommended that obvious codes, such as 1111 or 1234, not be used.
When a temporary 6-digit code is inadvertently repeated for different users, or
one user’s code is another’s duress code, the lower user number will take
priority (only the lower user number’s code is active).
Do not assign sequential codes 1 digit apart from each other (ex. 4096, 4097,
4098) as this will cause a Duress to be sent each time (one user’s code is
another user’s duress code).
Enter Master Code
Press CODE
key
Enter User # (03-70)
Enter 4-digit temporary code to be assigned.
-30-
Zobrazit stránku 29
1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 79 80

Komentáře k této Příručce

Žádné komentáře