ADEMCO LYNX Uživatelský manuál stáhnout pdf (Strana 6)

- 6 -

TO PROGRAM SYSTEM STATUS, & RESTORE REPORT CODES (

✱

59–

✱

76, &

✱

89):

With a 3+1 or 4+1 Standard Format:

Enter a code in the

first

box: 1–9, 0, B, C, D, E, or F. Enter "#+10" for 0, "#+11" for B,

"#+12" for C, "#+13" for D, "#+14" for E, "#+15" for F.

A "0" (

not

"#+10") in the

first

box will disable a report.

A "0" (

not

"#+10") in the

second

box will result in automatic advance to the next field when programming.

With an Expanded or 4+2 Format:

Enter codes in

both

boxes (1st and 2nd digits) for 1–9, 0, or B–F, as described above.

A "0" (

not

"#+10") in the

second

box will eliminate the expanded message for that report.

A "0" (

not

"#+10") in

both

boxes will disable the report.

With Ademco Contact ID Reporting:

Enter any digit (other than "0") in the

first

box, to enable zone to report (entries in the

second

boxes will be ignored).

A "0" (

not

"#+10") in the

first

box will disable the report.

Examples: For Code

(single digit), enter: 3 | 0

For Code

3 2

(two digits), enter: 3 | 2

For Code

B 2

(Hexadecimal), enter: #+11 | 2

SYSTEM STATUS REPORT CODES (

59–

68)

Field Function Programmed Values [ ] = Table 1 Default Value

✱

EXIT ERROR REPORT CODE

[1]

2nd digit is automatically sent as 2nd digit of the zone alarm report

code programmed in

✱

56, if expanded or 4+2 reporting is selected.

✱

TROUBLE REPORT CODE

[1,0]

✱

BYPASS REPORT CODE

[0,0]

✱

AC LOSS REPORT CODE

[0,0]

✱

LOW BAT REPORT CODE

[1,0]

✱

TEST REPORT CODE

[1,0]

✱

OPEN REPORT CODE

†† [0

] (††

2nd digit is automatically sent as the user

number if expanded

or 4+2 reporting is selected.)

✱

ARM AWAY/STAY RPT CODE

†† [0,0]

AWAY STAY

✱

RF XMTR LOW BAT REPORT CODE

[1,0]

✱

CANCEL REPORT CODE

[1,0]

RESTORE REPORT CODES (

70–

76)

✱

ALARM RESTORE RPT CODE

[1]

2nd digit is automatically sent as 2nd digit of the zone alarm report

code programmed in

✱

56, if expanded or 4+2 reporting is selected.

✱

TROUBLE RESTORE RPT CODE

[1,0]

✱

BYPASS RESTORE RPT CODE

[0,0]

✱

AC RESTORE RPT CODE

[0,0]

✱

LOW BAT RESTORE RPT CODE

[1,0]

✱

RF XMTR LO BAT RST RPT CODE

[1,0]

✱

TEST RESTORE RPT CODE

[0,0]

Field Function Programmed Values[ ] = Table 1 Default Value

OUTPUT AND SYSTEM SETUP (

80–

92)

✱

DEVICE PROGRAMMING MENU MODE

✱

ZONE LISTS MENU MODE

Program *80 and *81 only if Powerline Carrier Devices or chime by

zone are to be used. See procedure later in this manual.

✱

ENHANCED SEQUENTIAL MODE. See procedure later in this manual.

1 2 3 4 5 6 7 8 9 10 11 ... 15 16

Komentáře k této Příručce

Žádné komentáře

ADEMCO LYNX Uživatelský manuál Strana 6

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu ADEMCO LYNX