ADEMCO 4160-12 C-COM Specifikace stáhnout pdf (Strana 48)

P=ition the (user-supplied)st=d~ httery ad connect th supplied

connector cable ass-blies to the httery in wr~lel as follows, but

DO N~ CONNS~ TO THE No. 685 ~T.

Standby is necusary in order to

prevent messages ad the date and time ?rom being lmt during an AC ‘–’

power fafiore, even if it is otiy mmentary.

Do not attempt to use

the No. 685 without battery bacbp. The No. 685 contaim a built-in

charger.

The No. 685 is intended to be used with s 12 volt 55 AH (minimum)

maintenanc~free standby battery such as a Globe CC 12550. This is a

55 AH battery that will provide up to 9 boors standby (U.L. re~irea 4

hours).

In non-UL listed applications, if the power outage can be espected to

be very short (such aa when a standby generator is avaflable ) , a

standard sealed lead-acid battery [such as m Ademco No. 63o (12V, 5

AH)] may be used to supply bachp power.

Connect hth mnnector =bles provided in par~lel to the battery but

DO NOT COW~ T~M TO THS RRAR OF T~

No. 685 YST.

Splice the two RED wires together and connect them to the

positive (+) side of the battery.

b. Similarly connect the two BMCK wires to the negative (-) side of

the battery.

R~ove the top cover f- the Ho. 685 by rwoving 4 screws.

R-eve

dl patting material.

Obervs

tk slot co@iwatioos shown in Diagr= 3 in order to tecome

f~iar with the locations ofi Memory Card, ~U Card, Display Driv@

Card, Line Cards.

Note that slots J2 and J5 are, and shotid rmain,

=PtY .

R-on the

mmory card f- Slot J3 and set its BLDS ~per pl~ aa

d=cribed in Section V:

MSMORY CARD SETUP PRO~DURE .

R~ove the option PRW tip (No. 691) f~ the m=ory card, pro~= it

as rewred and r~~~ it aa descri~d in Section VI:

OFTION PROM

CH~ FOR MESSAGE LIGHTS, ENGLISH LANGUAGE PRINTER OUTPUTS AND

OPERAT~G OPTIONS.

Use a No. 692-1 PROM Removal Tool when removing

the PROM and a No. 692 PROM Insertion Tool when r-inserting the PHOM.

R*tiert the m=~y card in slot J3. Push down on the plastic tabs

untfl it snaps into plain.

~ sure that the ~splay driver and @U boards are f~y seated in

slots J1 md J4 respectively.

Set up and i=ert the ltie cards as described in Section VII: L~

CARD SETUP PROCEDURE. Start with slot J6 for line card #1 and

proceed, in semence, to slot J7 (line ad #2), sl~ J8 (line ~rd

#3), etc.

Do mt forget to mnnect the appropriate Wlari=d @one

line plug to the connector at the top ri@t aide of each line card. ‘+

Up to 8 line cards @n be accommodated by the No. 685 (see CAUTION on

pretioua page).

1 2 ... 43 44 45 46 47 48 49 50 51 52 53 ... 67 68

Komentáře k této Příručce

Žádné komentáře

ADEMCO 4160-12 C-COM Specifikace Strana 48

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu ADEMCO 4160-12 C-COM