ADEMCO Alpha Vista Console Manuál s instrukcemi stáhnout pdf (Strana 17)

REMOTE KEYSWITCH OPERATION & WIRING

An optional Remote” Keyswitch may be used for remote arming and disarming (this

is an installer-programmed option) .

A normally–open momentary switch is

connected across Zone 7 (which must be given up as a protection zone). A

momentary short of the zone will arm the System in the AWAY mode; if the key is

held (short maintained) for over 3 seconds, the System will arm in the STAY

mode. When a momentary short is applied subsequently, the System will disarm. A

keyswitch tamper (normally-closed) switch wired in series with zone 7 will

disable keyswitch operation until the system is next disarmed via a keypad, if

activated.

Refer to Diagram 2 for KeysWitch wiring details.

Note:

Regardless

whether End-of–Line supervision

is selected or not (in

Address *41),

an end-of–line resistor must still be used for

functioning of the keyswitch.

----- ----- ____

(AHMED} lREADYI

CONNECTS TO

REMOTE KEYPAD

INTERFAcE ON 4140

(SEE DIAG. 1)

NOTE:

No. 4073.70 IS NOT A

#11~

RED

GREEN

REMOTE

KEYPAO

CONNECTOR

BLUE

[

RED (PIN 31

TO FLYING LEAOS

GREEN

ON 10. PIN REMOTE

BLIJE IPIN 6)

KEYPAO CONNECTOR

GREEN IPIN 6)

REO

TAMPER

SWITCH WAC I

TOTS2-11

[

TO414O

TERMINAL BLOCK

LOCK

TB2

SWITCH (N O )

TO TB2-10

SUGGESTED PARTS FoR REMOTE KEYSWITCH

No, 9787 lVPE SLIM @XN3LE LEO PLATE

No. 112 N,C, TM4PER SW77CH

EOLR

No. 4073.70 HIGN SECURllY KEYIOCK, SPRING LOADED IN.O.I

U.L USTEO ITEM.

N3707.1O 1O-PIN MALE.TC-MAI.E AOAPTER [LEO lNTERFiCE) ‘

6A4131-10 IWPIN CONNECTCR W77N 1.E#Lk3

I ‘--------------J

proper

Diagram 2.

KEYSWITCH WIRING

Optional Remote Keypad Connection (4131/4147)

An optional remote keypad (4131 or 4147) may be used with the System. Two 10-pin

female connectors have been supplied for keypad interfacing to the 4140 control

board (see Diagram 1, Summary of Connections) .

Each connector

is equipped with

color-coded flying leads that are 12 inches (30 cm) in length.

One of the 10-pin connectors

is attached directly to the mating 10-pin male

connector on the 4131 or 4147 remote keypad (the connector can only be inserted

one way,

and will lock in place) .

The other connector is

connected to the 4140 control board via a male-to-

male 10–pin adapter (supplied). See Diagram 1.

INSTALLATION OF No. 4152LM AND WIRING TO

l?o. 4208

The optional No. 4152LM Loop Module is instailed onto the Digital Canmunication

Interface board as follows, referring to Diagram 3.

Note:

The Digital Caomunication

Interface board must be mounted onto the

main circuit board (in accordance with the Supplementary Installation

Instructions supplied) before proceeding with steps a, b, and c.

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 67 68

Komentáře k této Příručce

Žádné komentáře

ADEMCO Alpha Vista Console Manuál s instrukcemi Strana 17

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu ADEMCO Alpha Vista Console