ADEMCO Vista-128B PLUS Průvodce nastavením stáhnout pdf (Strana 2)

– 2 –

Table of Contents

Recommended Programming Procedure.........................3

Program Field Index .......................................................4

VISTA-128BP/VISTA-250BP Programming Form ............5

Partition-Specific Fields ................................................ 12

Programming With #93 Menu Mode.............................. 14

Zone Programming....................................................... 15

5800 Series Transmitters Loop Designations................. 19

Expert Mode Zone Programming .................................. 20

Report Code Programming ...........................................24

Alpha Descriptors Programming.................................... 27

Alpha Descriptor Vocabulary......................................... 31

Device Programming.................................................... 32

Output Programming .................................................... 35

Relay Voice Descriptors ............................................... 39

Relay Voice Descriptors and Custom Word Substitutes

Vocabulary ............................................................... 40

Custom Word Substitutes for VIP Module Annunciation. 40

Scheduled Check-in ..................................................... 41

System Layout Worksheets .......................................... 42

Output Devices Worksheets ......................................... 57

Scheduling Menu Prompts............................................ 63

Scheduling Worksheets................................................ 64

VISTA-128BP Summary of Connections Diagram ......... 69

VISTA-250BP Summary of Connections Diagram ......... 70

VISTA-128SIA Summary of Connections Diagram ........ 71

NOTE: All references to the VISTA-128BP also pertain to the VISTA-128SIA. The differences between the two panels

are outlined in the supplement accompanying the VISTA-128SIA. The supplement must be referred to when

programming the VISTA-128SIA. All references in this manual for number of zones, number of user codes, number of

access cards, and the event log capacity, use the VISTA-250BP’s features. The following table lists the differences

between the VISTA-128BP/128SIA and the VISTA-250BP control panels. All other features are identical, except for the

Remote Keypad Sounder (field 1✴

✴✴

✴46 option 2), which is available only in the VISTA-128BP/128SIA.

Feature VISTA-128BP/128SIA VISTA-250BP

Number of Zones 128 250

Number of User Codes 150 250

Number of Access Cards 250 500

Event Log Capacity 512 1000

VistaKey Modules 8 15

The purpose of this document is to provide a quick and easy way to program your entire system. A recommended

programming procedure is included, followed by a list of program fields with the corresponding program group they belong to

(system-wide, partition-specific, scheduling, etc.). Two program forms are included. One contains all the programming fields,

and the other contains the partition-specific fields. If you are setting up a single-partition system, the partition-specific fields

become system-wide fields.

Following the program forms are system layout worksheets. We recommend that you use these sheets to plan your system

before programming is performed. If you need further information about specific programming options, see the

VISTA-

128BP/VISTA-250BP Installation and Setup Guide

Make sure that one two-line alpha keypad is connected to the control and is set to device address "00."

Single-Partition System

The system default is for a single-partition system. Use the VISTA-128BP/VISTA-250BP SINGLE PARTITION

PROGRAMMING FORM when programming for single-partition usage. Follow the steps outlined in RECOMMENDED

PROGRAMMING PROCEDURE of this document for proper programming procedure.

Multiple-Partition System

You must enter the number of partitions you are using in data field 2*00 to set the system for multiple partitions. Use the

VISTA-128BP/VISTA-250BP SINGLE PARTITION and the PARTITION-SPECIFIC PROGRAM FORMS when

programming the system for multiple partitions. Follow the steps outlined in RECOMMENDED PROGRAMMING

PROCEDURE of this document for proper programming procedure.

SUMMARY OF PROGRAMMING COMMANDS

• To enter program mode, enter installer code + [8] + [0] + [0] + [0]

• To set standard defaults, press ✱97

• To change to next page of program fields, press ✱94

• To return to previous set of fields, press ✱99

• To erase account and phone number field entries, press [✱] + field number + [✱]

• To assign zone descriptors, press #93 + follow menu prompts

• To add custom words, press #93 + follow menu prompts

• To enter Installer's Message, press #93 + follow menu prompts

• To exit program mode, enter ✱99 OR ✱98: ✱99 allows re-access to programming mode by installer code.

✱98 prevents re-access to programming mode by installer code.

Standard default (✱97) values are shown in brackets [ ], otherwise default = 0.

1 2 3 4 5 6 7 ... 71 72

Komentáře k této Příručce

Žádné komentáře

ADEMCO Vista-128B PLUS Průvodce nastavením Strana 2

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu ADEMCO Vista-128B PLUS