ADEMCO Security System VISTA-15 Specifikace stáhnout pdf (Strana 26)

Interactive Mode Programming (

∗

56, *57,

∗

58,

∗

79,

∗

80,

∗

81,

∗

82)

Entering Interactive Mode

Press [

∗

] + [Interactive Mode No.] (for example,

∗

56) while in Program Mode.

The Alpha display keypad will display the first of a series of prompts

requesting entries.

After making the appropriate entry, press the [

∗

] key to accept the entry and

continue to the next prompt.

Loading Factory Defaults/Initializing for Download

To Load Default Entries

Press

∗

97 while in Program Mode. This resets all data fields to the default

values shown on the Program Form. Use

∗

97 only if you wish to return to the

original factory-programmed defaults.

To Initialize Download ID

Press

∗

96 while in Program Mode. This initializes the system for

downloading and resets all the subscriber account numbers and CSID.

Do not press

✱

97 to load defaults if any programming has been done previously—data already

programmed into the system will be changed!

Exiting the Programming Mode

Prevent installer code reentry

Press

∗

98. Exits Programming Mode and prevents re-entry by:

Installer Code + [8] + [0] + [0]. To enter the programming mode if

∗

98 was

used to exit, you must first power the system down. Then power up again,

and press [

∗

] and [#] at the same time, within 50 seconds of powering up.

See field *88 for other Program mode lockout options.

Allow installer code reentry

Press

∗

99. Exits Programming Mode and allows re-entry by:

Installer Code + [ 8] + [0] + [0] or by: Pressing [

∗

] and [#] at the same time,

within 50 seconds of power-up.

Table of Device Addresses

This Device Uses Address

Reports as

††

Enabled By…

RF Receiver 00 100 *56 zone programming: input device type entry

Long Range Radio 03 103 automatic if output to long range radio field *29 enabled

4286 Voice Module 04 104 automatic if phone module access code field *28 enabled

Zone Expanders (4219/4229):

module 1 (for zones 09 - 16)

module 2 (for zones 17 - 24)

module 3 (for zones 25 - 32)

module 4 zones 33 - 40

module 5 zones 41 - 48

†

107

108

109

110

111

*56 zone programming: input device type entry, then:

automatic if zone no. 9-16 entered as AW type or relay assigned

automatic if zone no. 17-24 entered as AW type or relay assigned

automatic if zone no. 25-32 entered as AW type or relay assigned

automatic if zone no. 33-40 entered as AW type or relay assigned

automatic if zone no. 41-48 entered as AW type or relay assigned

Relay Modules (4204):

module 1

module 2

module 3

module 4

†

112

113

114

115

*79 output device programming: device address prompt:

entered at device address prompt

Keypads:

keypad 1

keypad 2

keypad 3

keypad 4

keypad 5

keypad 6

keypad 7

keypad 8

n/a

data field programming as listed below:

always enabled for partition 1, all sounds enabled.

data field *190

data field *191

data field *192

data field *193

data field *194

data field *195

data field *196

5800TM Module 28 n/a automatic

† 4219/4229 addresses 9-11 and 4204 addresses 14-15 apply to the VISTA-20P.

†† Addressable devices are identified by “1” plus the device address when reporting. Enter a report

code for zone 91 to enable addressable device reporting (default = reports enabled). See field *199

for addressable device (ECP) 3-digit/2-digit identification keypad display options.

Installation Instructions

3-6

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 87 88

Komentáře k této Příručce

Žádné komentáře

ADEMCO Security System VISTA-15 Specifikace Strana 26

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu ADEMCO Security System VISTA-15