ADEMCO Security System VISTA-15 Specifikace Strana 70
- Strana / 88
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Keypad Functions
The following is a brief list of system commands. For detailed information concerning system
functions, refer to the User's Manual.
Voice Keypads
The 6150V/6160V Voice Keypads provide the following features:
• Message Center, which lets the user record and playback one message.
• Voice Status, which can announce system status by using the STATUS key.
• Voice Chime, which can alert users to the opening of doors/windows while the system is disarmed.
Refer to the User Guide for specific procedures for activating and using these features.
Keypad Commands
Function Description
Silence alarms Pressing any key will silence the keypad sounder for 10 seconds. Disarming the
system will silence both keypad and external sounders.
Quick Arm If enabled (field
∗
21), you can press [#] in place of the system's security code, plus
the desired arming key (Away, Stay, Instant, Maximum)
Single-Button arming If programmed (*57 Function Key menu mode), lettered keys A-D can be used for
arming, using options 3-AWAY, 4-STAY, 5-NIGHT-STAY, or 6-Step-Arming
If used, no security code is required to arm the system.
Alarm Memory When the system is disarmed, any zones that were in an alarm condition during
the armed period will be displayed. To clear this display, simply repeat the disarm
sequence (enter the security code and press the OFF key) again.
Arming Away Enter code + AWAY [2] or simply press appropriate lettered key on the keypads
(see “Single-Button Arming” above).
Arming Stay Enter code + STAY [3] or simply press appropriate key on the keypads (see “Single-
Button Arming” above).
Arming Night-Stay Enter code + STAY [3] + STAY [3] or simply press appropriate key on the keypads
(see “Single-Button Arming” above).
Arming Instant Enter code + INSTANT [7].
Arming Maximum Enter code + MAXIMUM [4] or simply press appropriate lettered key on the
keypads (see “Single-Button Arming” above).
Disarming Enter code + OFF [1].
If entry delay or an alarm is active, you do not need to
press OFF.
Bypassing Zones Enter code + BYPASS [6] + zone number(s).
Forced (Quick) Bypass To automatically bypass all faulted zones, use the “Quick Bypass” method. Enter
code + BYPASS + [#], then wait for all open zones to be displayed. Arm when
display indicates “ZONE BYPASSED” and “READY TO ARM”.
Chime Mode Enter code + CHIME [9]. To turn chime off, enter code + CHIME again.
Activate Output Devices If relay outputs (via a 4204, or 4229), or Powerline Carrier devices are used, two
keypad entries available to the user are included. If programmed, these entries can
be used to manually activate or deactivate the device(s) for starting or stopping
some action, such as turning lights on or off, etc. These keypad entries are:
[Security Code] + # + 7 + [2-digit Device #] activates (starts) that device.
[Security Code] + # + 8 + [2-digit Device #] deactivates (stops) that device.
SUMMARY OF ARMING MODES
Features for Each Arming ModeArming Mode
Exit Delay Entry Delay Perimeter Armed Interior Armed
AWAY Yes Yes Yes Yes
STAY Yes Yes Yes No
NIGHT-STAY Yes Yes Yes
only those zones
listed in Night-
Stay zone list
INSTANT Yes No Yes No
MAXIMUM Yes No Yes Yes
Installation Instructions
12-2
- 9,67$3366HULHV 1
- 9,67$36HULHV 1
- SOUNDING OF FIRE NOTIFICATION 2
- APPLIANCES 2
- Table Of Contents 3
- SECTION 1 5
- Capabilities 5
- Functions 5
- Compatible Devices 6
- SECTION 2 7
- Cabinet and Lock 7
- Wiring to Keypads 9
- Sounder (Bell) Connections 10
- Backup Battery 11
- Earth Ground 11
- Hardwire Zones 12
- Smoke Detectors (continued) 13
- Installing the Transmitters 14
- Installing the RF Receiver 14
- Installing a 5800TM Module 14
- Installing a Keyswitch 15
- Connecting Relay Modules 16
- Powerline Carrier Devices 17
- Installation Instructions 18
- Long Range Radio Connections 19
- AAV Connections 19
- Programming Overview 21
- Pager Programming 22
- Function Keys 23
- Output Devices 23
- Zone Type Definitions 23
- Mechanics of Programming 25
- Data Field Programming 27
- Zone Sounds & Timing ( 28
- Dialer Programming ( 29
- Miscellaneous System Fields 32
- Pager Programming Fields 35
- Symphony (AUI) Enable 39
- Keypad Programming Fields 39
- Zone Programming 41
- 43
- Completing Zone Programming 44
- Entd A022-4063 47
- Rcvd A022-4064 47
- Output Device Programming 49
- Activated By 52
- Zone List 52
- Zone Type 52
- Zone Number 53
- Output Action 53
- Output Number 53
- Summary Screen 53
- Zone Lists 55
- Function Key Programming 57
- Alpha Descriptor Programming 59
- Adding Custom Words 61
- CUSTOM WORD ? 61
- ALPHA VOCABULARY LIST 62
- Italicized 62
- Creating Schedules 63
- HH MMAM 64
- 0=NO 1=YES X 64
- System Communication 65
- Ademco Contact ID 66
- System Operation 69
- Keypad Functions 70
- Setting the Real-Time Clock 71
- Testing the System 73
- Go/No Go Test Mode 74
- 1=DIAL, 0=WALK 75
- SECTION 14 77
- SECURITY CONTROL 77
- COMPATIBLE DEVICES 77
- System Sensor 78
- 5802CP Belt Clip (Personal 79
- Emergency) 79
- Same as 5802 79
- Regulatory Agency Statements 81
- UL NOTICES 82
- Limitations and Warranty 83
- (Continued) 84
- – INDEX – 85
- SUMMARY OF CONNECTIONS 87
- ADEMCO LIMITED WARRANTY 88
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu ADEMCO Security System VISTA-15
(80 stránky)
(16 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.214 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce