ADEMCO Security System VISTA-15 Specifikace stáhnout pdf (Strana 34)

FIELD TITLE and DATA ENTRIES EXPLANATION

*92

Phone Line Monitor Enable

Entry 1–Timeout:

0 = disabled

1-15 = 1 minute to 15 minutes respectively

(2 = 2 min, 3 = 3 min, etc.; # + 10 =10 min, #

+ 11 = 11 min, # + 12 = 12 min, # + 13 = 13

min, # + 14 = 14 min, # + 15 = 15 min)

Entry 2–Display/Sound:

0 = keypad display only when phone line is

faulted.

1 = keypad display plus keypad trouble

sound when line is faulted. Each

partition turns off its own trouble sound.

No automatic timeout.

2 = Same as “1” plus programmed output

device STARTS. If either partition is

armed, external sounder activates.

External sounder will be turned off by

normal bell timeout, or by security code

plus OFF from either partition (it does

not have to be the one that was armed).

Entry 1:

Sets the length of time a phone line fault must remain after

detected before the second digit option is activated.

Entry 2:

Selects the desired phone line fault response.

Option 2 may be used even if a relay unit or Powerline carrier device

is not connected to the control.

Programmed Output Device must either be programmed to be

STOPPED in field ∗80 or STOPPED by entry of [security code] + [#]

+ 8 + device number. Partition in ∗80 should be set to “0,” for STOP.

Field *92 must be enabled for fire alarm installations, UL

commercial burglar alarm installations and UL residential burglar alarm

installations.

If the control unit is used on a UL commercial burglar alarm system

which requires 2 methods of remote communication, then the control

unit’s DACT and the other method of signal transmission must monitor

each other against communication failure and line fault. The fault must

be received and annunciated within 200 seconds of its occurrence.

*93

No. of Reports In Armed Period

per Zone (Swinger Suppression)

0 = unlimited number of reports

1 = 1 report per zone per armed period

2 = 2 reports per zone per armed period

This option can be used to limit the number of alarm/alarm restore

messages per zone sent to the central station in an armed period.

UL installations must be 0 (unlimited reports).

*94

Download Phone Number

Enter up to 20 digits as follows: 0–9, # +11

for “

∗

”, # + 12 for “#”, # + 13 for a pause.

Enter the phone number of the downloading computer.

Do not fill unused spaces. End field by entering ∗. To clear entries

from field, press ∗94∗.

*95

Ring Count For Downloading

0–15 = number of rings before control picks

up phone line .

†

NOTE:

If “15” is entered to bypass an

answering machine, and a 4285 or 4286

Phone Module is included in the system,

you should note the following:

When calling in from an off-premises

phone, the user should make the initial

call, allow 1 or 2 rings only, then hang

up, then call again. The phone module

will now seize the line, and 2 long tones

sound, followed by the usual voice prompt

for the access code. If this procedure is

not followed, phone module operation will

not be possible.

Refer to the chart below and program this field accordingly.

phone answer down-

module machine loading Set field

∗

95 to…

yes no no 1-14 (not 0)

yes yes no higher than number of rings set on

answer machine (e.g., if ans.

machine is 4 rings, set this field to

5). This allows access to the phone

module if the answer machine is off.

yes no yes 1-14 (not 0)

yes yes yes 15 (bypasses answer machine

†

)

no no no 0

no yes no 0

no no yes 1-14

no yes yes 15

*96

Command to Initialize CSID and

Subscriber Account Number

This is a command function, not a data field. Use this command, if

necessary, to reset all subscriber account numbers and the internal

CSID to the factory default values.

*97

Command to Reset System to

Factory Default Values

This is a command function, not a data field.

Pressing

∗

97 resets

all data fields to the factory default values (shown on the

Program Form).

IMPORTANT:

Do not press

∗

97 to load defaults if any

programming has been done previously— data already

programmed into the system will be changed!

*98

Command to Exit Program Mode

(with installer code lockout)

Exits Programming Mode and prevents re-entry by:

Installer Code + [8] + [0] + [0]. To enter the programming

mode if

∗

98 was used to exit, you must first power the system

down. Then power up again, and press [

∗

] and [#] at the same

time, within 50 seconds of powering up.

See field *88 for other Program mode lockout options.

*99

Command to Exit Program Mode

Exits Programming Mode and allows re-entry by:

Installer Code + [ 8] + [0] + [0] or by: Pressing [

∗

] and [#] at

the same time, within 50 seconds of power-up.

Installation Instructions

4-8

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 87 88

Komentáře k této Příručce

Žádné komentáře

ADEMCO Security System VISTA-15 Specifikace Strana 34

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu ADEMCO Security System VISTA-15