ADEMCO Security System VISTA-15 Specifikace stáhnout pdf (Strana 72)

Various System Trouble Displays

Alpha Display Fixed Disp. Meaning

CANCELED ALARM CA

will appear if an exit or interior zone contained a fault during closing at the time

the Exit Delay ended (e.g., exit door left open), but the system was disarmed

during the Entry Delay time. The alarm sounder and keypad sound continuously,

but stop when the system is disarmed. No message will be transmitted to the

central station.

EXIT ALARM EA

will appear when the Exit Delay ends if an exit or interior zone contained a fault

during closing. The alarm sounder and keypad sound continuously until the

system is disarmed (or timeout occurs). An “Exit Alarm” message is sent to the

central station. Also results if an alarm from an exit or interior zone occurs

within 2 minutes after the end of an Exit Delay.

CHECK CHECK

indicates that a problem exists with the displayed zone(s) and requires attention.

Note: The control will sense a high resistance in the loops on hardwired zones 2–8

and display “CHECK” and the affected zone number when the system is in the

disarmed mode. It will not be possible to arm the system as long as this condition

exists (unless this zone is bypassed). If the system is in the armed mode when the

high resistance condition occurs, this display will not appear, but will do so as

soon as the system is disarmed. Check the sensor or the loop wiring for the

displayed zone.

ALARM 1xx 1xx

indicates that communication between control and a zone expander or wireless

FAULT 1xx 1xx

receiver is interrupted, where “xx” is the device address. Check the wiring and

CHECK 1xx 1xx

DIP switch settings on the units.

If field *199 is set to “1,” all ECP module problems are displayed as “91.”

If there are wireless sensors in the system, the Check condition may also be

caused by some change in the environment that prevents the receiver from

receiving signals from a particular sensor.

SYSTEM LO BAT BAT

with no zone number indicates that the system's main standby battery is weak.

LO BAT BAT

with a zone number and a once-per-minute beeping at the keypad indicates that a

low-battery condition exists in the wireless sensor displayed (zone “00” indicates a

wireless keypad). If the battery is not replaced within 30 days, a “CHECK”

display may occur.

NOTE: Some wireless sensors contain a non-replaceable long-life battery which

requires replacement of the entire unit at the end of battery life (e.g., Nos. 5802,

5802CP).

TELCO FAULT 94

Telephone Line Failure, indicates that a monitored telephone line (if programmed

in field *92) has been cut or disconnected. Depending on how the system was

programmed, the keypad may also produce a trouble sound, and the external

sounder may be activated. Silence by entering installer code + OFF.

Busy-Standby dl

If this remains displayed for more than 1 minute, the system is disabled.

Modem Comm CC

The system is in communication with the central station for change of function or

status verification.

no display no display

Power Failure

If there is no keypad display at all and the LEDs are unlit, operating power (AC

and battery) for the system has stopped and the system is inoperative.

If the message “AC LOSS” (Alpha display keypads) or “NO AC” (Fixed-Word

display keypads) is displayed, the keypad is operating on battery power only.

If the battery standby capacity is used up during a prolonged AC power outage,

the control's power will shut down to minimize deep discharge of the battery.

Comm. Failure FC

A communication failure has occurred.

Open Circuit OC

The keypad is not receiving signals from the control and sees an open circuit.

Long Rng Trbl bF

Backup LRR communication failure.

Bell Failure

Bell supervision failure.

RCVR Jam

RF jam detected.

KEYPAD LOW BAT 00 BAT

Wireless keypad low battery

Phone Okay Cd

The dialer test has been successful (CID code 601).

Dialer Off dO

The dialer is disabled.

Test in Progress dd

Walk test mode is active(CID code 607).

Upload Completed dC

The upload or download session was completed.

Upload Failed dF

The upload or download session failed before completion.

Installation Instructions

12-4

1 2 ... 67 68 69 70 71 72 73 74 75 76 77 ... 87 88

Komentáře k této Příručce

Žádné komentáře

ADEMCO Security System VISTA-15 Specifikace Strana 72

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu ADEMCO Security System VISTA-15