ADEMCO VISTA-20HWse Průvodce řešením problémů stáhnout pdf (Strana 48)

–48–

DOWNLOAD

INFORMATION

(

94,

95)

94 DOWNLOAD PHONE NUMBER

Ê | | | | | | | | | | | | | | |

Enter up to 16 digits as follows: 0–9, # +11 for “

”, # + 12 for “#”, # + 13 for

a pause. Do not fill unused spaces. End field by entering

. To clear

entries from field, press

95 RING DETECTION COUNT FOR DOWNLOADING 0

0-15 = number of rings before control picks up phone line

Refer to the chart below and program this field accordingly.

NOTE: If "15" is entered

in field *95 to bypass an

answering machine, and

a 4285 Phone Module is

included in the system,

you should note the

following:

When calling in from an

off-premises phone, the

user should make the

initial call, allow 1 to 3

rings only, then hang up.

The user should then call

again. The Phone

Module will now seize

the line, and 2 long tones

sound, followed by the

usual voice prompt for

the 2-digit access code.

If this procedure is not

followed, Phone Module

operation will not be

possible.

ÊPhone Answering

Module ÊÊMachine Downloading Field

Yes No No Set for value other than “0” (1–14). This

will enable the control panel to answer the

phone call. Otherwise, it will not be possible to access the Phone

Module

Yes Yes No Set for a value higher than the number of

rings for which the answering machine is set.

Example: if machine is set for 4 rings, use a value of 5 or higher. This

is recommended so that the Phone

Module can still be accessed if the answering

machine is turned off and does not

answer the phone call.

Yes No Yes Set for value other than “0” (1–14).

Yes Yes Yes Enter “15” to bypass answering machine.

No No No Enter “0”.

No Yes No Enter “0”.

No No Yes Enter 1–14.

No Yes Yes Enter 15. See note at left.

OTHER PROGRAMMING

COMMANDS

56 ZONE PROGRAMMING MODE

Interactive menu mode used for programming zone attributes and report

codes. Refer to

ZONE PROGRAMMING

section for procedure.

80 OUTPUT DEVICES

Interactive menu mode applicable only if field *25 is programmed for a

4229, 4204, or if Powerline Carrier devices are being used. Refer to the

OUTPUT DEVICES

section for detailed procedure.

81 ZONE LISTS FOR OUTPUT DEVICES

Interactive menu mode applicable only if *25 is programmed for a 4229,

4204, or if Powerline Carrier devices are being used. Refer to the

ZONE

LIST

section for detailed procedure.

82 CUSTOM ALPHA EDITING

Interactive menu mode used to program zone descriptors. Refer to the

ALPHA DESCRIPTION PROGRAMMING

section for procedure.

96 INITIALIZE DOWNLOAD ID AND SUBSCRIBER ACCT. No. FOR

DOWNLOADING

Pressing *96 initializes the system for downloading.

97 SET ALL PROGRAM FIELDS TO DEFAULT VALUES

Pressing

97 automatically loads all defaults and erases any information

previously programmed.

98 EXITS PROGRAMMING MODE

Prevents re-entry by : Installer Code + 8 + 0 + 0

Allows re-entry only by Power-up then [

] and [#].

99 EXITS PROGRAMMING MODE

Allows re-entry to program mode by: Installer Code + 8 + 0 + 0 or

by Power-up then [

] and [#].

1 2 ... 43 44 45 46 47 48 49 50 51 52 53 ... 83 84

Komentáře k této Příručce

Žádné komentáře

ADEMCO VISTA-20HWse Průvodce řešením problémů Strana 48

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu ADEMCO VISTA-20HWse