ADEMCO 4140XMPT2 Uživatelský manuál stáhnout pdf (Strana 104)

– 104 –

#83 USER SCHEDULING MENU MODE

General Information The system provides up to 20 "timers" which will be available to the end user for

the purpose of controlling output devices (4204 or X-10). These timers are

analogous to the individual appliance timers that might be purchased at a

department store. The typical uses for this feature could be control of lights or

appliances , typically via X-10 modules. These modules are programmed into the

system by the installer during #93 Menu Mode–Device Programming. The end

user needs only to know the output device number and its alpha descriptor.

The installer may set certain relays to be "Restricted" during # 93 Menu Mode-Relay

Programming. These relays may not be controlled by the end user. (Prevents end-

user from controlling doors, pumps, etc.

To enter this mode, the User enters CODE + # + 83

Output Timer # ?

01-20,00=Quit 01

Enter the output timer number to be programmed (1-20).

Press * to accept entry and move to the next prompt.

Enter 00 to quit and return to normal mode.

06 07:00P 11:45P

PORCH LITE 04

If that timer number has already been programmed, a

summary screen will appear. In this example:

06 = Timer #

04 = Output Device # affected by this timer

PORCH LITE = Output Descriptor for Device # 4

07:00PM = Start Time

11:45PM = Stop Time

Press * to continue.

06 ENTER OUTPUT#

PORCH LITE 04

Enter the desired output number (1-16)

As the number is entered, the descriptor changes to

indicate which output device is being affected.

Note: 00 entered as the output # deletes the timer

(Timer 06 in this example) and displays an output

descriptor of "None". Devices are programmed via #93

Menu Mode.

06 ON TIME ?

07:00 PM

Enter the ON time in 00:01 - 11:59 format.

When the display shows the desired time, press the *

key to go forward to the AM/PM field. In this field, any of

the keys 0-9 may be used to toggle the AM/PM

indication. Enter 00:00 to skip. Note: Could use 2

commands to perform an ON one day and an OFF

another day

06 OFF TIME ?

11:45 PM

Enter the OFF time in 00:01 - 11:59 format.

When the display shows the desired time, press the *

key to go forward to the AM/PM field. In this field, any of

the keys 0-9 may be used to toggle the AM/PM

indication. Enter 00:00 to skip.

Note: Could use 2 commands to perform an ON one day

and an OFF another day

06 Days? MTWTFSS

Hit 0-7 x x

To select the days which are to be activated, enter 1-7

(Monday = 1). An "X" will appear under that day,

indicating the output for that day is active. Entering a

day's number again will deactivate that day. Pressing 0

will toggle all days on/off.

The outputs will only be in effect for the days which have

the letter x underneath them. As the week progresses,

the selected days are reset to the deactive state, unless

the permanent option is selected (next screen prompt).

When completed, press * to continue.

06 Permanent ?

0 = NO,1 = YES 0

Permanent means continue executing these commands

on a continuous basis. An answer of 0 means execute

each day's output only once. The letter "x" under the day

will then be cleared.

Press * to accept entry. The system will quit scheduling

mode and return to normal mode.

1 2 ... 99 100 101 102 103 104 105 106 107 108 109 ... 131 132

Komentáře k této Příručce

Žádné komentáře

ADEMCO 4140XMPT2 Uživatelský manuál Strana 104

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu ADEMCO 4140XMPT2