ADEMCO 4140XMPT2 Uživatelský manuál stáhnout pdf (Strana 22)

– 22 –

Note On RF Keys

(5801, 5803, etc.)

5800 series RF keys can be used to arm and disarm the system. These

transmitters include the 5801, 5803, 5804, and any other 5800 series transmitter

if programmed for one of zone type responses 20-22. These transmitters are tied

to a user in order to provide a record of who armed or disarmed the system.

Because of this, an RF button will not arm or disarm a system unless it has been

assigned to a user, which is done during the "add a user" function (see Add A

User Code section). In addition, when the user is deleted from the system, the

key is deactivated. To test whether the keys are assigned to users or not, use the

test mode. When the appropriate button is pressed, the corresponding zone will

be displayed on the console and will remain there until test mode is terminated.

Wireless Zone Types Each RF zone can be programmed to respond as any zone type such as

ENTRY/EXIT, INTERIOR, PERIMETER, etc. (see the ZONE TYPES section for a

complete explanation of each zone type).

Desired alarm responses for 5700 series devices are as follows:

ZONE TYPE TRANSMITTER ID #

Entry/Exit Burg 1 through 47 *

Perimeter Burg 1 through 47 *

Interior Burg 1 through 47 *

32 through 47 * (5775)

Fire 48 through 63 *

48 through 55 ** (5706)

24 Hour Panic 48 through 63*

(silent or audible) 62 or 63 *** (5701)

Day/Night Burglary 1 through 47 *

24 Hour Auxiliary 1 through 47 *

NOTES:

* Note that zones 1-63 can be used, but have the following limitations: Transmitters set

for zones 48-55 will transmit once every 12 seconds while the zone is faulted.

Transmitters set for zones 56-63 will transmit once every 3 seconds while faulted.

These two ranges of zone numbers could adversely affect transmitter battery life.

Transmitters set for an ID of 32 through 47 will have a 3 minute lock-out between

transmissions. Use this last range of zone ID numbers for sensors protecting

frequently used doors or windows to conserve battery life.

** Transmitter IDs 48 through 55 have highest signal priority.

*** Transmitter IDs 62 and 63 are unsupervised to allow removal of the 5701 off premises

-- signal priority is lower than that of fire, but higher than burglary.

Advisories 1. Do not place transmitters on or near metal objects. This will decrease range

and/or block transmissions.

2. Place the receiver in a high, centrally located area for best reception. Do not

place receiver on or near metal objects.

3. For maximum range, the RF receiver must be at least 10 feet (3m) from the

Control panel or any remote consoles to avoid interference from their

microprocessor.

4. If dual receivers are used:

A. Both must be at least 10 feet (3m) from each other, as well as from the

Control panel and remote consoles.

B. The house IDs must be the same.

C. Using two Receivers does not increase the number of transmitters the

system can support (63 transmitters, plus a wireless keypad).

Fault Annunciation Since the polling loop and the RF receiver(s) are shared among the 8 partitions,

the scheme for annunciating their failure is as follows:

Respective faults (for zones 88-91 & 97) will report as trouble conditions only, and

as such, should be assigned either zone type 00 if no annunciation is desired, or

zone type 05 if annunciation as trouble condition is desired. If the polling loop or

RF link fails, the corresponding zone number will display a trouble condition for

each partition that uses the device that failed. In addition, all zones associated with

that device will indicate a fault condition. The trouble condition will not interfere

with the ability to arm the partition, but the faults must first be bypassed.

NOTE: 5800 series transmitters have built-in tamper protection and will

annunciate as a "CHECK" condition unless field *24 is disabled.

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 131 132

Komentáře k této Příručce

Žádné komentáře

ADEMCO 4140XMPT2 Uživatelský manuál Strana 22

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu ADEMCO 4140XMPT2