ADEMCO 4140XMPT2 Uživatelský manuál stáhnout pdf (Strana 60)

– 60 –

2*19 Use Partition Descriptors

Enter 1 if partition descriptors will be programmed. If enabled, the normal

console display will include a partition number and the partition descriptor (if

programmed in #93 Menu Mode). Entering 0 causes the consoles to

display a non-partitioned system type of display (no partition no. appears).

Scheduling & Relay Output

Options

Second Page Fields

1*74 Relay Timeout XX Minutes

Enter the relay timeout, 0-127 in multiples of 2 minutes, desired for #80

Menu Mode time driven event relay command numbers "04/09" and #93

Menu Mode Relay Programming output command "56" (refer to #93 and

#80 Menu Mode sections in this manual).

1*75 Relay Timeout YY Seconds

Enter the relay timeout, 0-127 seconds, desired for #80 Menu Mode

time driven event relay command numbers "05/10" and #93 Menu Mode

Relay Programming command "57" (refer to #93 and #80 Menu Mode

sections in this manual).

Third Page Fields

2*01 Daylight Savings Time Start/End Month

Enter the months 00-12 in which daylight savings time starts and ends.

Enter 00, 00 if daylight savings time does not apply to the user's region.

Standard setting for U.S. is 04,10.

2*02 Daylight Savings Time Start/End Weekend

Enter the start and end weekends for daylight savings time as follows:

1=first; 2=second; 3=third; 4=fourth; 5=last; 6=next to last; 7=third from

last. Standard setting for U.S. is 01,05.

2*11 Allow Disarm Outside Window If Alarm Occurs

Used only if field 2*10 (partition-specific field) is set to 1. Enter 1 if it is

desired that the system can be disarmed outside the programmed disarm

window if an alarm has occurred. Enter 0 if it is desired that disarming can

only be done during the disarm window, regardless of system status. If field

2*10 is set to 0 for a partition, this field (2*11) has no effect for that partition.

2*13-2*14 Scheduling Related Dialer Reports

Enter the report codes for the scheduling related events as shown on the

programming form.

Event Logging Options 1*55 Date Format Selection

Select the desired date format where 0 = mmddyy; 1 = ddmmyy

1*56 60Hz/50Hz Real Time Clock Synchronization

Enter the appropriate value where 0 = 60Hz Mains; 1 = 50Hz Mains.

1*70 Event Log Types

Enter 1 for each of the types of events for which event logging is

desired, as shown on the programming form. Otherwise enter 0.

1*71 12/24 Hour Time Stamp Format

Select the type of time stamping desired: 0=standard 12 hour; 1= 24

hour format.

1*72 Event Log Printer On-Line

Enter 1 to enable the printer to print events as they occur, or 0 to enable

the printer such that the logs are only printed upon request.

1*73 Printer Baud Rate

Enter 0 if printer is configured for 1200 baud (preferred). Enter 1 if printer

is configured for 300 baud.

Alarm Verification 1*60 Alarm Verification

Enter 1 if alarm verification is used. Otherwise enter 0.

1*66 Silence Bells During Alarm Verification

Enter 1 if audio alarm verification is used. Otherwise enter 0.

1*67 Video Alarm Verification Selection

Enter 1 if video alarm verification is used. Otherwise enter 0.

1 2 ... 55 56 57 58 59 60 61 62 63 64 65 ... 131 132

Komentáře k této Příručce

Žádné komentáře

ADEMCO 4140XMPT2 Uživatelský manuál Strana 60

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu ADEMCO 4140XMPT2