ADEMCO 4140XMPT2 Uživatelský manuál Strana 15
- Strana / 132
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
– 15 –
BASIC 9 HARD-WIRED ZONES
Zone 1 The following table summarizes zone 1 characteristics.
Applications Can be used for EOLR supervised or closed circuit
unsupervised devices. It is the only zone that supports
2-wire smoke detectors.
Zone Response Type: Any
Response Time 350 msec
Max. Zone Resistance 100 ohms, excluding EOLR
Unsupervised Usage • Cut red PCB jumper.
• Only closed circuit devices can be used.
EOLR Supervised • Leave red PCB jumper intact.
• Supports both open circuit and closed circuit devices.
• Connect open circuit device in parallel across the loop.
The 2,000 ohm EOLR must be connected across the
loop wires at the last device.
• Connect closed circuit device in series with the loop.
EOLR Fire Zone: • Leave red PCB jumper intact.
• Assign zone type 09 (fire)
• Supports up to sixteen (16) 2-wire smoke detectors.
• Second CODE + OFF sequence momentarily
interrupts power to reset the smoke detectors.
• See table below for compatible detectors.
Compatible Smoke Detectors
Detector Type Device Model #
Photoelectric w/heat sensor, direct wire...................... System Sensor 2300T
Photoelectric plug-in head........................................ System Sensor 2600EC
Photoelectric, direct wire ......................................... System Sensor 2400
Photoelectric w/heat sensor, direct wire...................... System Sensor 2400TH
Photoelectric w/B401B base..................................... System Sensor 2451
Photoelectric w/heat sensor & B401B base ................. System Sensor 2451TH
Ionization, direct wire.............................................. System Sensor 1400
Ionization w/B401B base ......................................... System Sensor 1451
Ionization plug-in head ............................................ System Sensor 1600EC
Photoelectric duct detector
w/DH400 base ....................................................... System Sensor 2451
Ionization duct detect. w/DH400 base ........................ System Sensor 1451DH
Zone 1 Advisories
If the EOLR is not at the end of the loop, the zone is not properly supervised. The
system may not respond to an open circuit within the zone.
The alarm current provided by this zone is sufficient to support operation of only
one detector in the alarmed state.
UL NOTE: EOLR are required for UL installations.
Zone 9 The following table summarizes zone 9 characteristics.
Applications This zone is unsupervised and is suitable for monitoring
fast acting glass break sensors or vibration sensors when
programmed for fast response.
Response Type Any type except fire
Response Time Normal (350 msec) or Fast (10msec) selected in field *14.
Max. Zone Resistance 300 ohms
Unsupervised Usage • Only closed circuit devices can be used.
• Connect these devices in series with one another
between terminals 22 & 23.
Zone 9 Advisories
Avoid using mechanical magnetic or relay type contacts in this zone when
programmed for fast response.
- 4140XMPT2 1
- CONGRATULATIONS! 2
- TABLE OF CONTENTS 3
- INSTALLATION INSTRUCTIONS 6
- SUMMARY OF SYSTEM FEATURES 7
- SCHEDULING OVERVIEW 12
- BASIC 9 HARD-WIRED ZONES 15
- Wire Gauge Max. Length 17
- J7 CONNECTOR 25
- 4142TR CABLE 25
- 1 2 3 4 5 6 7 8 9 26
- IST OF START 29
- URN ON LIGHTS 29
- ELL OUTPUT 30
- TROBE LIGHT 30
- YSTEM STATUS INDICATORS 30
- ONFIRMATION OF ARMING DING 30
- NLOCK EXIT DOORS 31
- URN ON EMERGENCY LIGHTING 31
- OUNDING FOR WIRELESS KEYPAD 31
- Section 3 32
- REMOTE CONSOLES, SOUNDERS 32
- & PHONE CONNECTIONS 32
- Wire Gauge Maximum Length 33
- EXTERNAL SOUNDERS 34
- PHONE CONNECTIONS 34
- Section 4 35
- POWERING THE SYSTEM 36
- (total poll loop worksht) 37
- Section 7 39
- Section 8 41
- PROGRAMMING GUIDE 42
- 00-15; 00=no suppression 43
- RF Trans. Type 46
- Section 2 50
- INDEX TO PROGRAMMING FIELDS 53
- DATA FIELD DESCRIPTIONS 54
- (refer to #93 and 60
- — 61 — 61
- Selected Partitio 61
- Set of Fields 61
- — 63 — 63
- 2nd Page Fields 63
- ALPHA VOCABULARY 75
- CHARACTER (ASCII) CHART 75
- COMMUNICATION FORMATS 76
- Code Definition 78
- COMMUNICATION PROGRAMMING 79
- NOTES Note: Low Speed will 80
- Section 6 DOWNLOADING 85
- DIRECT WIRE DOWNLOADING 87
- INTRODUCTION TO SCHEDULING 88
- Note that 00 is 89
- #80 SCHEDULING MENU MODE 92
- Number (HH:MM) (HH:MM) 93
- Hol. Partition 94
- Mon/Day 1 2345678 94
- HOLIDAY NUMBER ? 99
- Action Codes: 100
- 01 RELAY GRP # ? 100
- GROUP ? 12345678 100
- ACCESS SCHED # ? 101
- MON A1 Window 1? 101
- MON A3 Window 2 ? 101
- Hol A1 Window 1 ? 101
- Hol A1 Window 2 ? 101
- #83 USER SCHEDULING MENU MODE 104
- SYSTEM OPERATION 105
- Section 1. SYSTEM OPERATION 106
- User 3 User 5 108
- Level 1 Level 4 108
- Master Oper B 108
- KEYPAD FUNCTIONS 111
- Part. 1 WHSE 112
- User 01 Auth.=1 112
- PRINTER DTR 114
- BYPASS EVENT LOG 115
- SYSTEM EVENT LOG 115
- DIP SWITCH POSITION 121
- 4275EX PIR 122
- 4194 REED CONTACT 122
- (SURFACE MOUNT) 122
- 4278EX PIR 122
- IMPORTANT 123
- SET SWITCHES WITH 123
- BATTERY REMOVED 123
- Section 6. SPECIFICATIONS 124
- WARNING! 130
- RINGER EQUIVALENCE: 0.7B 131
- © 1996 PITTWAY CORPORATION 132
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu ADEMCO 4140XMPT2
(88 stránky)
(61 stránky)
(132 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.290 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce