ADEMCO Security System VISTA-15CN Průvodce nastavením Strana 95
- Strana / 132
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
19–1
SECTION 19
Alpha Descriptor Programming
••••••••••••••••••••••••••••••••••••••••••••••••••
In This Section
♦
About Alpha Descriptor Programming
♦
Zone Descriptors
♦
Programming Zone Descriptors
♦
Adding Custom Words
••••••••••••••••••••••••••••••••••••••••••••••••••
About Alpha Descriptor Programming
This section provides instructions for programming alpha zone descriptors. This is
recommended for systems using alpha keypads, and a 4285 or 4286 VIP Module.
If you are using a 4285/4286 VIP Module, select from those words/numbers in the Alpha
Vocabulary List shown in boldface type. The phone module does not provide annunciation
of the other words/numbers.
If a 4285/4286 VIP Module is added to an existing VISTA-15/VISTA-15CN system, the alpha
descriptors presently in the system should be reprogrammed, selected from those words/numbers
shown in
boldface
type
in the Alpha Vocabulary List. The phone module does not provide
annunciation of any other words/numbers.
The Alpha Vocabulary List and Character (ASCII) Chart are on page 19-4.
Zone Descriptors
For the alpha keypad used with the VISTA-15/VISTA-15CN, you can program into the
system a user-friendly English language description/location of all protection zones, keypad
panics, and RF receiver supervision faults. Each description can be composed of a
combination of words/numbers (up to 3) selected from a vocabulary of 196 words/numbers
stored in memory (see a following page). In addition, up to 10 installer-defined
words/numbers can be added to those already in memory. Thus, when an alarm or trouble
occurs in a zone, an appropriate description for that zone's location is displayed at the
keypad.
NOTE: Alpha descriptor entry can be done locally at the alpha keypad or remotely using
downloading software. The alpha keypad entry procedure is described below.
Programming Zone Descriptors (Program Menu Mode
✴
82)
You can enter the descriptor when the zone is being defined in field
✱
56, but we recommend
you do it using
✱
82 Menu mode.
To program zone descriptors, enter the 3-digit reference number for the desired word(s). The
3-digit number
for each word is provided in the Alpha Vocabulary List (on page 19-4).
1. With the system powered up, enter the Programming mode by keying:
Installer code (4 1 1 2) + 8 + 0 + 0. The following display appears:
Installer Code
20
Program Alpha?
0=No, 1=Yes 00
2. Press
✱
82.
The
Program Alpha?
prompt appears.
- 9,67$ 1
- 9,67$&1 1
- Table of Contents 4
- List of Figures 7
- Introduction 9
- Installing the Control 13
- V15-01-V0 14
- RCVR BRD 15
- TERMINALS 16
- ON CONTROL 16
- Wiring the AC Transformer 17
- Section 12: Final Power-Up 18
- Installing Remote Keypads 19
- Mounting the Keypads 20
- AUX. DATA 21
- Basic Hardwired Zones 1–6 23
- 2000 OHMS 24
- Programming Hardwired Zones 26
- Wired Zone Expansion 27
- DISARMED 29
- READY TO ARM 29
- Wireless Expansion 31
- < < 32
- Installing the 5800TM Module 33
- Jam Detection and Reporting 33
- Appendix A 36
- 1 2 3 4 5 37
- Powerline Carrier Devices 41
- Programming Relay Outputs 42
- 4285 & 4286 VIP Module 43
- Section 11: 44
- Audio Alarm 44
- Verification (AAV) Unit 44
- 4285 or 4286 45
- VIP MODULE 45
- External Sounders 47
- Sounder Connections and Power 48
- Sounder Supervision 48
- Testing the Sounder 48
- Long Range Radio 49
- Dynamic Signaling Feature 50
- 1 2 3 4 5 6 52
- Final Power-Up 53
- Battery Tests 54
- Mechanics of Programming 55
- Loading Factory Defaults 57
- Exiting the Programming Mode 57
- Section 18. Zone Lists 61
- Data Field Descriptions 63
- ZONE SOUNDS & 65
- TIMING ( 65
- Interactive 69
- Zone Programming 77
- 79
- To Remove a Zone 82
- Section 16 - Zone Programming 85
- Output Device Programming 87
- Zone Lists 93
- Cross Zoning - Zone List 04 94
- NIGHT-STAY - Zone List 05 94
- Alpha Descriptor Programming 95
- Summary Mode Display 96
- ALPHA VOCABULARY LIST 98
- CHARACTER (ASCII) CHART 98
- Remote Programming and 99
- Control (Downloading) 99
- Initial Download 100
- Remote Programming Commands 100
- System Communication 101
- FORMAT TYPE DESCRIPTION 102
- System Operation 105
- Keypad Functions 106
- Setting the Real-Time Clock 110
- Testing the System 111
- Troubleshooting Guide 113
- SMOKE DETECTOR 114
- CONTACTING TECHNICAL SUPPORT 115
- In This Section 117
- APPENDIX A 121
- Regulatory Agency Statements 123
- Warnings and Limitations 125
- VISTA-15/VISTA-15CN 131
- SUMMARY OF CONNECTIONS 131
- Copyright 132
- 2000 PITTWAY CORPORATION 132
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu ADEMCO Security System VISTA-15CN
(20 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce